Environmental Housings for Telonics Equipment

Available from:
The Sexton Company LLC dba Sexton Photographics
860 E Street NE
Salem, Oregon 97301-1223
Voice: 503-371-6239
Fax: 503-371-0994
DUNS: 015 902 695
FEIN: 93-13100880
Email: kens@thesextonco.com
See our web site at: www.thesextonco.com

Environmental housings from The Sexton Company are designed to protect your delicate telemetry equipment against most of the hazards of fieldwork. Built of durable acrylic plastic, with captive doors and self-aligning connectors, these housings fully offset the effects of rain, snow, mud, salt spray, sand, debris, and submersion throughout the life of your Telonics equipment.

Installation
The only preparation necessary to install your Telonics equipment into its environmental housing is to exchange the original Telonics aluminum knobs with the plated brass U-joint halves provided with the housing (Allen wrench included). This need only be done once, as the Telonics equipment can be used outside the housing using the U-joint halves as knobs.

To install the Telonics unit, slip it into the open top of the housing, close the top cover using the alignment provided by the self-contacting connectors, and latch the top. To remove the equipment from the housing, unlatch the top cover, lift the top cover straight up to disengage the connectors, and pull the equipment out of the housing.

Bump Cases
Bump cases are provided with each housing to protect the acrylic box from shock damage and from the greenhouse effect of a closed, clear box gaining heat in sunlight. They are made from light-colored 1/4 inch closed cell Neoprene® with Nylon® on both sides, and have an attached adjustable shoulder strap. All seams are double cemented and sewn for durability. The cases add about 1/2 inch to all housing dimensions and weigh about 1/2 pound. 

Specifications
All housings are made from 1/4 inch [6mm] acrylic, buna-N O-ring seals, stainless steel spring latches, control shafts, and hardware. Connectors are plated brass. They are waterproof to a depth of 1 meter for 30 minutes. They feature captive access doors to prevent loss or misalignment. After initial installation of universal joints, insertion, removal, and operation of the equipment is done without tools. All external connectors (antenna, headphones, battery charger) are self-aligning and self-connecting. Each housing includes a spares kit with O-ring grease, spare O-rings, and appropriately sized Allen wrench(es).

Consult The Sexton Company for custom modifications to these housings, and for custom underwater housings for still, motion picture, video, and flash equipment, as well as for data loggers, cine sync slates, and other instruments. Please see our web site for ideas and recent projects.

Warranty

• The manufacturer inspects and tests each housing for watertight integrity before it is delivered.
• The manufacturer will repair or replace at manufacturer’s option any housing which proves to be defective in construction or materials within one year of date of delivery.
• The manufacturer is not liable for damage to equipment caused by leakage of water into the housing, nor is the manufacturer liable for loss of data or income therefrom as may result from such leakage. The manufacturer is not liable for any accidents during which this housing was in use.
• This warranty is void in the event of negligent handling of the housing, including, but not limited to, dropping the housing, modifications to the housing by other than the manufacturer, improper care of the sealing components, and exceeding the specified depth limitation of 1 meter.
• There is no express or implied warranty, nor warranty of merchantability, except as stated by the manufacturer above.
• The buyer understands that, because of the nature of this product, he/she uses the housing at his/her own risk and agrees to hold the manufacturer harmless, except as stated above.

Terms
Orders are accepted on a Prepaid basis. Payment must be Certified or Cashier's check, Company or Organizational check, or Money Order in U. S. Dollars. We now accept VISA, MC, Discover, and AmEx. Net Terms may be granted on a case-by-case basis. If Net Terms are granted, failure to pay on time will result in permanent reversion to Prepayment for that customer.

Orders
Orders may be placed by mail, fax, email, or phone. Orders may be placed on-line by email from our web site. Such orders will be accepted and confirmed by return email, which will also assign the expected ship date. Be sure to have payment arrive at The Sexton Company prior to expected ship date, unless prior arrangements have been made for terms.

Delivery
It is our policy to ship from stock within 2 working days when available, but not all models are regularly stocked. If housings are not in stock, the standard shipping date is 4 weeks from receipt of pre-paid order. Faster delivery is available for additional cost as follows:

3 weeks, add 30%
2 weeks, add 60%
1 week, add 100%

Shipping
Prices above include packaging, insurance, and pre-paid shipping by UPS Ground or US Mail to destinations within the continental USA. Charges for air express or overseas shipment will be added to invoice or invoiced separately.

Brand names used in this document are registered trademarks of their respective companies.

This price list is effective July 15, 2001, and supersedes all previous lists. Prices and specifications are subject to change without notice.

The Sexton Company has been supplying housings for Telonics telemetry equipment since 1979, and has manufactured custom underwater housings for cameras and other instruments since 1973.

The Sexton Company LLC dba Sexton Photographics
860 E Street NE
Salem, Oregon 97301-1223
Voice: 503-371-6239
Fax: 503-371-0994
DUNS: 015 902 695
FEIN: 93-13100880
Email: kens@thesextonco.com
See our web site at: www.thesextonco.com